Pre-drywall housing for new builds. Secured to joists via hanger bars. IC Rated and Air-Tight for safety and energy efficiency. Rugged galvanized steel with built-in thermal protection.
4″ New Construction Airtight Recessed Light Housing – E26 Base
The 4-inch New Construction Airtight Recessed Light Housing with E26 base brings unmatched fixture flexibility to new ceiling builds. Supporting standard E26 LED bulbs as well as compatible trims, this housing adapts to a wide range of lighting preferences without replacing the can. Combined with IC-rated, airtight construction and pre-wired quick-connect hardware, it delivers a code-compliant, future-ready rough-in platform for residential and light commercial new construction projects. Model :401HA Wattage :MAX 15W Voltage :120V~277V Hole size :113MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
4″ New Construction Airtight Recessed Light Housing Universal Bulb Compatibility Meets Energy-Code Construction.
Flexible Fixture Pairing: The E26 base accepts a wide range of standard LED bulbs and pairs with a wide selection of 4-inch trims. Insulation-Safe from Day One: IC-rated construction allows direct contact with ceiling insulation — no clearance gap, no fire-protection enclosures, no extra steps. Built-In Energy Compliance: The airtight body seals each ceiling penetration against conditioned air loss, meeting IECC and California Title 24 requirements out of the box.
6″ New Construction Recessed Light Housing – E26 Base
Shop 6-inch new construction recessed housing with E26 base. IC rated, compatible with standard LED bulbs and 6-inch trims, pre-wired quick connects, energy-code ready. Model :608HA Wattage :MAX 20W Voltage :120V~277V Hole size :162MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
6″ New Construction Recessed Light Housing E26 Flexibility Meets New Construction Reliability.
Trim & Bulb Freedom: The E26 medium base accepts standard LED bulbs and pairs with a broad selection of 6-inch compatible trims. Insulation-Safe Construction: IC-rated for direct contact with ceiling insulation — no clearance gap, no supplemental fire-protection enclosures, and no extra steps at rough-in. Built-In Energy Compliance: The airtight body seals each ceiling penetration to prevent conditioned air loss, meeting IECC and California Title 24 requirements out of the box.
4″ New Construction Airtight Recessed Light Housing – TP24 Connector
The 4-inch New Construction Airtight Recessed Light Housing delivers a certified, energy-efficient rough-in platform for new-build ceiling installations. Engineered with an airtight sealed body and IC-rated construction, this housing is built to meet stringent building codes while supporting a wide range of interior and wet/damp location applications. Model :408HA Wattage :MAX 15W Voltage :120V~277V Hole size :113MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
4″ New Construction Airtight Recessed Light Housing Engineered for Energy Compliance and Installation Speed.
Code-Ready Construction: The IC-rated, airtight housing meets energy code requirements out of the box, eliminating the need for additional sealing measures during inspection. Broad Ceiling Compatibility: Designed to perform in standard joist framing, T-grid, and drop ceiling systems, enabling seamless integration across diverse new construction environments. Flexible Location Coverage: Supports wet and damp location use cases when paired with the appropriate trim (sold separately), making it adaptable across living spaces and utility areas alike.
6″ New Construction Recessed Light Housing – TP24 Connector
The 6-inch New Construction Recessed Light Can establishes a professional-grade, code-compliant rough-in framework for new ceiling builds. Pre-wired with quick-connect hardware and independently certified to strict safety standards, this housing is built for contractors and electricians who demand reliable, fast installations. Model :608HA Wattage :MAX 20W Voltage :120V~277V Hole size :162MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
6″ New Construction Recessed Light Housing Pre-Wired, Certified, and Ready for Any New Build.
Installation-Ready Out of the Box: Pre-wired with quick-connect hardware, this housing eliminates the most time-consuming step of the rough-in process. Independent Safety Certification: Every unit is independently tested and certified against strict electrical and thermal safety benchmarks — providing project owners and inspectors the assurance they require.
Damp Location Versatility: Rated for damp locations, this housing is equally at home above a bathroom ceiling as it is in a residential kitchen or hallway.
4″ New Construction Shallow Recessed Light Housing – TP24 Connector
The 4″ Shallow New Construction Recessed Light Housing with TP24 Connector is built for efficient recessed lighting installation in new construction projects. Made from durable galvanized steel, this IC-rated housing supports 120V–277V applications and features quick connect push wire nuts to help simplify field wiring. A shallow profile makes it a practical choice where ceiling depth is limited. Model :408HICA Wattage :MAX 15W Voltage :120V~277V Hole size :113MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
4″ New Construction Recessed Light Housing Shallow New Construction Housing for Professional Installations.
Space-Saving Design: A compact 4-inch housing for new construction ceilings with limited installation depth. Efficient Wiring: TP24 connector and quick connect push wire nuts simplify rough-in connections. Flexible Applications: IC-rated design for insulated ceilings in residential, multifamily, retail, office, and hospitality projects.
6″ New Construction Shallow Recessed Light Housing – TP24 Connector
The 6″ New Construction Shallow Recessed Light Housing provides a professional, heavy-duty foundation for modern lighting installations in new ceiling frames. Featuring a slim profile and standardized TP24 connection, this housing is designed for seamless integration into diverse architectural layouts, ensuring a safe and efficient rough-in for high-performance recessed fixtures in residential and commercial projects. Model :608HICA Wattage :MAX 20W Voltage :120V~277V Hole size :162MM Material :Galvanized Steel Certificate :UL, ETL, Title 24/JA8, FCC Warranty :5 Years
6″ New Construction Recessed Light Housing High-Performance New Construction Housing for Shallow Plenums.
Architectural Identity: A dedicated 6-inch housing engineered for new construction framing with limited overhead clearance. Core Safety Design: Integrated IC-rated and Air-Tight construction ensures optimal thermal management and building energy compliance. Project Application: Optimized for professional electrical rough-ins in high-end residential, multi-family, and commercial new builds.
Quick Connect Push Wire Nuts
The pre-installed junction box features high-spec quick-connect push wire nuts, facilitating tool-free electrical connections. This design streamlines the wiring process during the rough-in stage, significantly reducing labor costs for large-scale new construction lighting projects.
IC-Rated for Insulated Ceiling Applications
Specifically engineered for safety, this IC-rated housing is certified for direct contact with ceiling insulation. It eliminates the need for specialized fire-protection boxes or additional spacing, ensuring a code-compliant installation in insulated ceiling assemblies.
Adjustable Hanger Bars
Adjustable or breakaway design to fit different installation distances. The Hanger Bars can beadjusted according toneeds: 8 1/4″- 25 1/8″.
Installation Instructions
1. Telescopic bar hangers have been engineered to allow placing of housing between joists. Position hanger bars so that nails point away from housing and that hangers bars are aligned with bottom of joist. To secure fixture hammer nails to joists. Hanger bars can be shortened to fit 12″ framing by breaking at score line. (Fig 1)
2. Adjust the fixture for appropriate ceiling thickness by loosening the hex screws that attach the round housing to the plaster frame. Align the bottom edge of housing to ceiling line and tighten screws.(Fig 2)
3. ELECTRICAL CONNECTION: Open the snap-on junction box captive door and remove the appropriate pry-out with screwdriver. Luminaire has been designed to accommodate metallic conduit and non-metallic cable, metallic conduit must be used if local code requires it. Round knockouts are dedicated for metallic cables and rectangular knockouts are to be utilized for non-metallic cables. Connect supply leads to wires in fixture junction box. Connect white wire to white wire, black wire to black wire and green supply wire to bare copper wire with quick connectors. Provide electrical service to fixture per NEC and local electrical code from a suitable junction box to junction box located on fixture. Fixture must be supplied with wire rated for at least 90°C. Close the snap-on junction box door.(See Fig 3 and Fig.4)
1. Install hanger bars to fixture be sure end tab is facing outward. (FLG 1)
2. Junction box contains three wires a black (hot) white (neutral) and bare ground. MAKE SURE TO CONNECT WHITE TO WHITE ANDCOLORED OR BLACK TO BLACK (FIG.2) After completing the wiring. (being make sure sure the wires are placed with wiring box)snap wiring box cover closed.
3. Joists Type Ceilings: Extend bar hangers to fit between joist and position fixture and hammer nail on bars into the joists. Make sure the hanger is leveled with bottom of joists. (FIG.3)
4. T-bar Type Ceiling:Extend bar hangers 1″ past T-bars then rest fixture on t-bars.Secure fixture to t-bars with wire see.(FIG.4)
5. Plug in trim kit to can, insert trim into housing pushupward fully and pressure springs will hold trim in place. (FIG.5)
1. Joists Type Ceilings: Extend bar hangers to fit between joist and position fixture and hammer nail on bars into the joists. Make sure the hanger is leveled with bottom of joists.(Flg1)
2. Junction box contains three wires a black(hot) white(neutral)and bare ground. MAKE SURE TO CONNECT WHITE TO WHITE AND COLORED OR BLACK TO BLACK After completing the wiring.(being make sure sure thewires are placed with wiring box)snap wiring box coverclosed. (Flg2)
3. Making holes in drywall (Φ6 1/8″). (Fig. 3)
4. Plug in trim kit to can, insert trim into housing push upward fully and pressure springs will hold trim in place. (Fig. 4)
Frequently Asked Questions (FAQ)
1. 4″ New Construction Airtight Recessed Light Housing – E26 Base
Q1: Can this housing be covered by insulation?
A: Yes. The IC-rated design allows the housing to be in direct contact with ceiling insulation when installed according to applicable electrical codes and manufacturer requirements.
Q2: Is this housing airtight?
A: Yes. The airtight construction helps prevent air leakage through the ceiling opening, improves energy efficiency, and supports compliance with applicable building energy codes.
Q3: What type of light source is compatible with this housing?
A: This housing features an E26 base and is designed for compatible E26-base LED bulbs or lighting fixtures. Please verify the wattage rating and trim compatibility before installation.
2. 6″ New Construction Recessed Light Housing – E26 Connector
Q1: Is this housing compatible with ceiling insulation?
A: Yes. The IC-rated design allows direct contact with ceiling insulation without requiring an additional clearance gap, provided the installation complies with applicable codes and manufacturer instructions.
Q2: Is this housing pre-wired?
A: Yes. The junction box comes equipped with quick-connect push wire nuts to simplify electrical connections and help reduce installation time.
Q3: What type of light source can be used with this housing?
A: This housing is designed for compatible lighting fixtures using an E26 connection. Please confirm the light source’s wattage and physical compatibility before installation.
3. 4″ New Construction Airtight Recessed Light Housing – TP24 Connector
Q1: Can this housing be covered by insulation?
A: Yes. Its IC rating certifies it for direct contact with ceiling insulation when installed according to applicable electrical codes and manufacturer requirements.
Q2: Can I install this housing in a drop ceiling?
A: Yes. This housing is designed for installation in T-grid and drop ceiling systems, as well as traditional ceiling joist framing.
Q3: Is an additional airtight gasket required?
A: No. The airtight construction is integrated into the housing body and does not require a separate airtight gasket for the housing’s sealed design.
4. 6″ New Construction Recessed Light Housing – TP24 Connector
Q1: Is this housing compatible with insulation?
A: Yes. The IC-rated design allows the housing to be installed in direct contact with ceiling insulation without requiring an additional clearance gap, subject to applicable installation requirements.
Q2: Can this housing be installed in a bathroom?
A: Yes. It is suitable for damp-location applications when paired with a compatible damp-location-rated trim. Always verify the ratings of the complete lighting assembly before installation.
Q3: Is the housing pre-wired?
A: Yes. The junction box is factory-equipped with quick-connect push wire nuts to simplify wiring and help contractors complete installations more efficiently.
5. 6″ New Construction Shallow Recessed Light Housing – TP24 Connector
Q1: Can this housing be installed in a shallow ceiling cavity?
A: Yes. Its shallow-profile design makes it suitable for new construction projects where overhead clearance is limited.
Q2: Can this housing be used in an insulated ceiling?
A: Yes. The IC-rated construction is designed for direct contact with ceiling insulation when installed according to applicable electrical codes and manufacturer requirements.
Q3: Does this housing support airtight installation?
A: Yes. The airtight construction helps reduce air leakage through ceiling openings and supports building energy efficiency requirements.
6. 4″ New Construction Shallow Recessed Light Housing – TP24 Connector
Q1: What is this recessed light housing used for?
A: It is designed for 4-inch recessed lighting installations in new construction projects, particularly where ceiling depth is limited.
Q2: What voltage does this housing support?
A: This housing supports a voltage range of 120V–277V, making it suitable for a variety of residential and commercial lighting applications.
Q3: Is this housing IC-rated?
A: Yes. The IC-rated design allows direct contact with ceiling insulation when installed according to applicable electrical codes and manufacturer requirements.
Explore our products
Tableware
Glassware
Sanitary Bathroom Ware
Diesel Generator Sets
LED Lighting
IEC Motors
NEMA Motors
Pumps
Cookie Consent
We use cookies to improve your experience on our site. By using our site, you consent to cookies.
Cookie Preferences
Manage your cookie preferences below:
Essential cookies enable basic functions and are necessary for the proper function of the website.
Name
Description
Duration
Cookie Preferences
This cookie is used to store the user's cookie consent preferences.
30 days
Statistics cookies collect information anonymously. This information helps us understand how visitors use our website.
Google Analytics is a powerful tool that tracks and analyzes website traffic for informed marketing decisions.
Contains information related to marketing campaigns of the user. These are shared with Google AdWords / Google Ads when the Google Ads and Google Analytics accounts are linked together.
90 days
__utma
ID used to identify users and sessions
2 years after last activity
__utmt
Used to monitor number of Google Analytics server requests
10 minutes
__utmb
Used to distinguish new sessions and visits. This cookie is set when the GA.js javascript library is loaded and there is no existing __utmb cookie. The cookie is updated every time data is sent to the Google Analytics server.
30 minutes after last activity
__utmc
Used only with old Urchin versions of Google Analytics and not with GA.js. Was used to distinguish between new sessions and visits at the end of a session.
End of session (browser)
__utmz
Contains information about the traffic source or campaign that directed user to the website. The cookie is set when the GA.js javascript is loaded and updated when data is sent to the Google Anaytics server
6 months after last activity
__utmv
Contains custom information set by the web developer via the _setCustomVar method in Google Analytics. This cookie is updated every time new data is sent to the Google Analytics server.
2 years after last activity
__utmx
Used to determine whether a user is included in an A / B or Multivariate test.
18 months
_ga
ID used to identify users
2 years
_gali
Used by Google Analytics to determine which links on a page are being clicked
30 seconds
_ga_
ID used to identify users
2 years
_gid
ID used to identify users for 24 hours after last activity
24 hours
_gat
Used to monitor number of Google Analytics server requests when using Google Tag Manager
